Task Force Tips Active Fire Protection (AFP)

Pistol Grip - Yes Valve Design - Stainless Slide Valve Flow Rate - 10-125 gpm (40-500 l/min) Inlet Coupling Style - Knurled Body Size - 1" (25 mm) Inlet Coupling Swivel - Full Time Swivel Style - One Piece with Valve Pressure Mode - Single Type - Automatic Fog Teeth - Fixed Operating Pressure - 100 psi (7 bar) Remote Control - No Weight - 3.4 Bumper Material - Rubber - bonded  

Remote Control - No Profile - Low Profile Coupling Size Side A - 6" (150mm) Coupling Size Side B - 5" (125 mm) Weight - 16.95 Detent Swivel - No L D H Inlet - Yes L D H Outlet - Yes Pressure Relief Valve - Yes

AB Series - BIV - TFT's Ball Intake Valve has a 3.65" waterway and is designed for use with 3.5, 4, 4.5, 5 or 6" (89, 100, 115, 125 or 150mm) hose. The 30° intake elbow swivels 360° and has multiple positive detents. Make hose connections from any direction with minimal kinks and coupling stress. Designed for pressure or vacuum service on a pumper. Maximum operating pressure is 300 psi (20 bar). Meets 900 psi (62 bar) hydrostatic strength test. The aluminum castings are hard coat anodized, and TFT-powder coat finished inside and out for maximum corrosion protection. All the components on the wet side of the valve are made of stainless steel for additional corrosion protection. The hand crank needs 7-1/2 turns to open, meeting NFPA slow close requirements. There is a unique position indicator that shows the operator if the valve is open, closed or somewhere in between. The hand crank is installed with a 2-5/8" swing but may be switched to 1-5/8" if desired. The unit comes equipped with a rugged 3/4" (19mm) drain valve to quickly drain water from the valve housing. A port for an optional air bleed valve is incorporated into the design for user friendly configurability. Hose couplings and truck connections are attached to the valve using polymer bearing rings which provide electrical isolation to help prevent galvanic corrosion. Includes TFT's new adjustable pressure relief valve with a discharge that can be directed one of four ways and meets NFPA 1901. Contact TFT customer service for configurations not shown. Cap lanyard anchor point is standard.

AB Series - BIV - TFT's Ball Intake Valve has a 3.65" waterway and is designed for use with 3.5, 4, 4.5, 5 or 6" (89, 100, 115, 125 or 150mm) hose. The 30° intake elbow swivels 360° and has multiple positive detents. Make hose connections from any direction with minimal kinks and coupling stress. Designed for pressure or vacuum service on a pumper. Maximum operating pressure is 300 psi (20 bar). Meets 900 psi (62 bar) hydrostatic strength test. The aluminum castings are hard coat anodized, and TFT-powder coat finished inside and out for maximum corrosion protection. All the components on the wet side of the valve are made of stainless steel for additional corrosion protection. The hand crank needs 7-1/2 turns to open, meeting NFPA slow close requirements. There is a unique position indicator that shows the operator if the valve is open, closed or somewhere in between. The hand crank is installed with a 2-5/8" swing but may be switched to 1-5/8" if desired. The unit comes equipped with a rugged 3/4" (19mm) drain valve to quickly drain water from the valve housing. A port for an optional air bleed valve is incorporated into the design for user friendly configurability. Hose couplings and truck connections are attached to the valve using polymer bearing rings which provide electrical isolation to help prevent galvanic corrosion. Includes TFT's new adjustable pressure relief valve with a discharge that can be directed one of four ways and meets NFPA 1901. Contact TFT customer service for configurations not shown. Cap lanyard anchor point is standard.

AB Series - BIV - TFT's Ball Intake Valve has a 3.65" waterway and is designed for use with 3.5, 4, 4.5, 5 or 6" (89, 100, 115, 125 or 150mm) hose. The 30° intake elbow swivels 360° and has multiple positive detents. Make hose connections from any direction with minimal kinks and coupling stress. Designed for pressure or vacuum service on a pumper. Maximum operating pressure is 300 psi (20 bar). Meets 900 psi (62 bar) hydrostatic strength test. The aluminum castings are hard coat anodized, and TFT-powder coat finished inside and out for maximum corrosion protection. All the components on the wet side of the valve are made of stainless steel for additional corrosion protection. The hand crank needs 7-1/2 turns to open, meeting NFPA slow close requirements. There is a unique position indicator that shows the operator if the valve is open, closed or somewhere in between. The hand crank is installed with a 2-5/8" swing but may be switched to 1-5/8" if desired. The unit comes equipped with a rugged 3/4" (19mm) drain valve to quickly drain water from the valve housing. A port for an optional air bleed valve is incorporated into the design for user friendly configurability. Hose couplings and truck connections are attached to the valve using polymer bearing rings which provide electrical isolation to help prevent galvanic corrosion. Includes TFT's new adjustable pressure relief valve with a discharge that can be directed one of four ways and meets NFPA 1901. Contact TFT customer service for configurations not shown. Cap lanyard anchor point is standard.

Flotation device allows TFT high volume low-level strainer to collect clean water from ponds, lakes and rivers. The strainer inlet, made of hard anodized and powder-coated aluminum, hangs 18" below water level to avoid sucking surface air and bottom debris. Capable of supporting up to 30 ft of hose, the strainer extends well beyond safety ledges of residential ponds. The clog-resistant stainless steel filter has over twice as much flow area as a 6" hose. This keeps friction loss down to 0.5 psi (1" Hg) at 1500 gpm and reduces the potential for air vortexes to form. Oversized sealed ball pivot allows 45° range of hose angle without constricting the flow path. Jet Siphon substantially increases suction lift capability and is also useful for tank shuttle, pump priming and dewatering with no need for a trash pump. Jet Siphon has 1.5" female hose threaded coupling that pivots freely in any direction to avoid hose kinks. Rugged polyethylene float is yellow for high visibility and nests compactly over the strainer for minimal storage space. Float removal is not necessary for low level use, although a tethered latching hinge pin allows the float to be removed or installed instantly if desired. Coupling Size - 6" (150mm) Coupling Style - Handle Coupling Swivel- Non-Full Time Swivel Jet Siphon - Yes Jet Siphon Coupling Size - 1.5" (38 mm) Jet Siphon Coupling Style - Rocker Jet Siphon Coupling Swivel - Full Time Swivel Strainer Float - Yes Weight - 29.2 Connection Type - NH Female Finish - Stardust Silver Jet Siphon Connection Type - NH Female

Task Force AM8HNX10 is a 6 inch hard suction hose.

AB Series - BIV - TFT's Ball Intake Valve has a 3.65" waterway and is designed for use with 3.5, 4, 4.5, 5 or 6" (89, 100, 115, 125 or 150mm) hose. The 30° intake elbow swivels 360° and has multiple positive detents. Make hose connections from any direction with minimal kinks and coupling stress. Designed for pressure or vacuum service on a pumper. Maximum operating pressure is 300 psi (20 bar). Meets 900 psi (62 bar) hydrostatic strength test. The aluminum castings are hard coat anodized, and TFT-powder coat finished inside and out for maximum corrosion protection. All the components on the wet side of the valve are made of stainless steel for additional corrosion protection. The hand crank needs 7-1/2 turns to open, meeting NFPA slow close requirements. There is a unique position indicator that shows the operator if the valve is open, closed or somewhere in between. The hand crank is installed with a 2-5/8" swing but may be switched to 1-5/8" if desired. The unit comes equipped with a rugged 3/4" (19mm) drain valve to quickly drain water from the valve housing. A port for an optional air bleed valve is incorporated into the design for user friendly configurability. Hose couplings and truck connections are attached to the valve using polymer bearing rings which provide electrical isolation to help prevent galvanic corrosion. Includes TFT's new adjustable pressure relief valve with a discharge that can be directed one of four ways and meets NFPA 1901. Contact TFT customer service for configurations not shown. Cap lanyard anchor point is standard.

High volume low-level strainer is made of hard anodized and powder-coated aluminum. Clog-resistant stainless steel filter has over twice as much flow area as a 6" hose. This keeps friction loss down to 0.5 psi (1" Hg) at 1500 gpm and reduces the potential for air vortexes to form as water sinks towards the 2.5" minimum usable depth. Oversized sealed ball pivot allows 45° range of hose angle without constricting the flow path. Optional Jet Siphon with 1.5" female hose thread substantially increases suction lift capability. Jet Siphon substantially increases suction lift capability and is also useful for tank shuttle, pump priming and dewatering with no need for a trash pump. Jet Siphon has 1.5" female hose threaded coupling that pivots freely in any direction to avoid hose kinks. Coupling Size - 6" (150mm) Coupling Style - Handle Coupling Swivel - Non-Full Time Swivel Jet Siphon - Yes Jet Siphon Coupling Size - 1.5" (38 mm) Jet Siphon Coupling Style - Rocker Jet Siphon Coupling Swivel - Full Time Swivel Strainer Float - No Weight - 18.1 Connection Type - NH Female Finish - Stardust Silver Jet Siphon Connection Type - NH Female